菜单
  
    1. CONTENTS.
         Page.       Section.
             1      1. Contents.
             2      2. Installation.
                    2.0 Introduction.
                    2.1 Direct Mounting Units onto Kinetrol Positioner Actuators.
                    2.2 Mounting of Discrete Positioners.
                    2.3 Air and Electrical Connections.
             4      3. Schematic Functional Diagram.
             5      4. Set Up.
    4.0 Introduction
    4.1 Setting Travel Speed.
                    4.2 Setting Optional Limit Switch Cams.
                    4.3 Overview – Electronic Settings.
                    4.4 Default Settings and Reset Procedure.
                    4.5 Entering and Leaving Setup Mode.
                    4.6 Automatic Endstop Finding Procedure.
                   2. INSTALLATION 21477
    2.0 Introduction
           Positioners can be supplied direct-mounted, or ready to be direct-mounted, onto Kinetrol rotary actuators, or in stand- alone (discrete) form for fitting via a mount kit to any 90 degree rotary actuator. If the positioner is supplied ready mounted
    on an actuator, sections 2.1 and 2.2 can be bypassed. Positioner-type Kinetrol actuators (ready for direct mounting of positioners) are available in models 03 to 14 inclusive.
           These instructions cover the possible use of both metal and moulded feedback coupling. It is expected that most units will contain a moulded coupling.
    2.1 Mounting of Direct Mounting Units onto Kinetrol Positioner-Type Actuators

     
    2.1.1 Move actuator vane to mid travel position, with its output square as shown in Figure 1. This is essential to prevent subsequent error in orienting positioner square.
    2.1.2 Remove positioner cover, and undo the five M4 slot-headed screws holding the red plastic carrier plate into the body.
    Disconnect the two wires to the servo valve, and lift out the whole carrier plate assembly complete with shaft and circuit etc.
    2.1.3 Bolt the positioner body to the actuator in the orientation shown in Figure 1, taking care that O-rings are in place to seal the ports into the actuator, and that the actuator shaft is centred in its hole.
    2.1.4 (a) Metal coupling versions on 07 and larger models: fit anti-backlash spring over one corner of the actuator square as  shown in Figure 2.
        (b) Moulded coupling versions: on all direct mount versions, loosen central screw in coupling shaft so that the collet is  not closed, and fit coupling over shaft square.
    2.1.5 Observe the range of motion available to the positioner shaft, limited by the correct running of the potentiometer quadrant wheel, driven by the stainless steel strap (see Figure 3). Fit the carrier plate/shaft assembly back into the positioner box with the shaft near mid-range, “feeling” the female square in the positioner shaft onto the male actuator square while maintaining its position near mid range. It is essential that the two shafts are correctly oriented relative to each other, since if they are 90 degrees out, the quadrant wheel can be forced too far and damage done to the drive mechanism during subsequent actuator movements. It is possible to fit the positioner correctly with the actuator square at one end of its travel, but experience indicates a high probability of mistaking the direction of movement of the actuator – hence it is strongly advised that the positioner be fitted with the actuator square at the mid-travel position, where there is no ambiguity possible.
  1. 上一篇:顺流式填充床减阻英文文献和中文翻译
  2. 下一篇:冷却系统研究及注射模设计英文文献和中文翻译
  1. 汽车内燃机连杆载荷和应...

  2. 机械手系统英文文献和中文翻译

  3. 固体氧化物燃料电池英文文献和中文翻译

  4. 船舶运动仿真系统英文文献和中文翻译

  5. 新能源空调系统设计英文文献和中文翻译

  6. 正交试验回归法和响应曲...

  7. 机械设计制造及其自动化英文文献和中文翻译

  8. 中国传统元素在游戏角色...

  9. 浅析中国古代宗法制度

  10. 巴金《激流三部曲》高觉新的悲剧命运

  11. g-C3N4光催化剂的制备和光催化性能研究

  12. C++最短路径算法研究和程序设计

  13. NFC协议物理层的软件实现+文献综述

  14. 高警觉工作人群的元情绪...

  15. 现代简约美式风格在室内家装中的运用

  16. 江苏省某高中学生体质现状的调查研究

  17. 上市公司股权结构对经营绩效的影响研究

  

About

优尔论文网手机版...

主页:http://www.youerw.com

关闭返回