-
General all-steel punching die’s punching accuracy Accuracy of panel punching part is display the press accuracy of the die exactly. But the accuracy of any punching parts’ linear dimension and positional accuracy almost depend on the blanking and blanking accuracy,. So that the compound mould of compound punching’s accuracy, is typicalness and representation in the majority.33656
- 上一篇：预应力混凝土梁英文文献和中文翻译
- 下一篇：模具快速制造技术英文文献和中文翻译
Analyse of the die’s accuracy
For the analyse of pracyicable inaccuracy during production of dies to inactivation, we could get the tendency when it is augmentation in most time. From this we could analyse the elements. When the new punch dies pt into production to the first cutter grinding, the inaccuracy produced called initial error; if the die grinding more than twenty times, until it’s discard, the inaccuracy called conventional error; and before the dies discard, the largest error of the last batch permit, called limiting error. at job site, the evidence to confirm life of sharpening is the higher of the blanking, punched hole or punched parts. Because all finished parts had been blanked ,so it is especially for the compound dies. Therefore, the analyse of burr and measurement is especially important when do them as enterprise standardization or checked with <<the height of punching part>>.
The initial error usually is the minimal through the whole life of die. Its magnitude depend on the accuracy of manufacture, quality, measure of the punching part, thickness of panel, magnitude of gap and degree of homogeneity. The accuracy of manufacture depend on the manufacture process. For the 1 mm thicked compound punching part made in medium steel, the experimental result and productive practice all prove that the burr of dies which produced by spark cutting are higher 25%~~30% than produced by grinder ,NC or CNC. The reason is that not only the latter have more exact machining accuracy but also the value of roughness Ra is less one order than the formmer, it can be reached 0.025μm. Therefore, the die’s initial blanked accuracy depends on the accuracy of manufacture, quality and so on.
The normal error of the punch die is the practicable error when the fist cutter grinding and the last cutter grinding before the die produce the last qualified product. As the increase of cutter grinding, caused the measure the nature wear of the dies are gradual increasing, the error of punching part increase also, so the parts are blew proof. And the die will be unused. The hole on the part and inner because the measure of wear will be small and small gradually, and its outside form will be lager in the same reason. Therefore, the hole and inner form in the part will be made mould according to one-way positive deviation or nearly equal to the limit max measure. In like manner, the punching part’s appearance will be made mould according to one-way negative deviation or nearly equal to limit mini measure. For this will be broaden the normal error, and the cutter grinding times will be increased, the life will be long.
The limit error in punching parts are the max dimension error which practicable allowed in the parts with limit error. This kind of parts usually are the last qualified products before the die discard.
For the all classes of dies, if we analyse the fluctuate, tendency of increase and decrease and law which appeared in the die’s whole life, we will find that the master of the error are changeless; the error that because the abrade of the cutter and impression will be as the cutter grinding times increased at the same time. And that will cause the error oversize gradually; and also have another part error are unconventional , unforeseen. Therefore, every die’ s error are composed of fixed error, system error, accident error and so on.
1. fixed error
At the whole process when the New punching die between just input production to discard, the changeless master error that in qualified part are called fixed error. It’s magnitude is the deviation when the die production qualified products before the first cutter grinding. Also is the initial error, but the die have initial punching accuracy at this time. Because of the abrade of parts, the die after grinding will be change the dimension error. And the increment of deviation will oversize as the times of cutter grinding. So the punching accuracy after cutter grinding also called “grinding accuracy” and lower tan initial accuracy. The fixed error depend on the elements factor as followed :
-
汽车内燃机连杆载荷和应...
-
审计的优化管理英文文献和中文翻译
-
FPGA的全景拼接相机的优化...
-
气味源定位的有限时间粒...
-
PLC仿真的虚拟工厂英文文献和中文翻译
-
ZigBee-RFID混合网络的节电英文文献和中文翻译
-
PLC可编程控制器的介绍英文文献和中文翻译
上市公司股权结构对经营绩效的影响研究
浅析中国古代宗法制度
中国传统元素在游戏角色...
江苏省某高中学生体质现状的调查研究
NFC协议物理层的软件实现+文献综述
g-C3N4光催化剂的制备和光催化性能研究
现代简约美式风格在室内家装中的运用
高警觉工作人群的元情绪...
C++最短路径算法研究和程序设计
巴金《激流三部曲》高觉新的悲剧命运