菜单
  

    (3) The mold product level greatly is lower than the international standard
    The production cycle actually is higher than the international water broad product level low mainly to display in the mold precision, cavity aspect and so on surface roughness, life and structure .
    (4) Develops the ability badly, economic efficiency unsatisfactory our country mold enterprise technical personnel proportion low
    The level is lower, also does not take the product development, frequently is in the passive position in the market. Our country each mold staff average year creation output value approximately ,ten thousand US dollars, overseas mold industry developed country mostly 15 to10,000 US dollars, some reach as high as 25 to10,000 US dollars, relative is our country quite part of molds enterprises also continues to use the workshop type management with it, truly realizes the enterprise which the modernized enterprise manages few
    To create the above disparity the reason to be very many, the mold long-term has not obtained the value besides the history in as the product which should have, as well as the most state-owned enterprises mechanism cannot adapt the market economy, but also has the following several reasons: .
    (1) Country to mold industry policy support dynamics also insufficiently
    Although the country already was clear about has promulgated the mold profession industrial policy, but necessary policy few, carried out dynamics to be weak. At present enjoyed the mold product increment duty enterprise nation 185, the majority enterprise still the tax burden is only overweight. The mold enterprise carries on the technological transformations introduction equipment to have to pay the considerable amount the tax money, affects the technology advancement, moreover privately operated enterprise loan extremely difficult .
    (2) Talented person serious insufficient, the scientific research development and the technical attack investment too urine
    Mold profession is the technology, the fund, the work crowded industry, along with the time progress and the technical development, grasps the talented person which and skilled utilizes the new technology exceptionally short, the high-quality mold fitter and the enterprise management talent extremely is also anxious. Because the mold enterprise benefit unsatisfactory and takes insufficiently the scientific research development and the technical attack, the scientific research unit and the universities, colleges and institutes eye stares at is creating income, causes the mold profession invests too few in the scientific research development and the technical attack aspect, causes the mold technological development step not to be big, progresses not quick .
    (3) The craft equipment level to be low, also necessary is not good, the use factor low
    recent years our country engine bed profession progressed quickly, has been able to provide the quite complete precision work equipment, but compared with the overseas equipment, still had a bigger disparity. Although the domestic many enterprises have introduced many overseas advanced equipment, but the overall equipment level low are very more than the overseas many enterprises. As a result of aspect the and so on system and fund reason, introduces the equipment not not necessary, the equipment and the appendix not necessary phenomenon are extremely common, the equipment utilization rate low question cannot obtain the comparatively properly solution for a long time .
    (4) Specialization, standardization, commercialized degree low, the cooperation ability
    Because receives "large and complete" "small and entire" the influence since long ago, mold specialization level low, the specialized labor pision is not careful, the commercialized degree is low. At present domestic every year produces mold, commodity mold minister 40% About, other for from produce uses for oneself. Between the mold enterprise cooperates impeded, completes the comparatively large-scale mold complete task with difficulty. Mold standardization level low, mold standard letter use cave rare is low also to the mold quality, the cost has a more tremendous influence, specially has very tremendous influence .
  1. 上一篇:塑料注塑模具外文文献和中文翻译
  2. 下一篇:搅拌器机械密封容器英文文献和中文翻译
  1. 机械设计制造及其自动化英文文献和中文翻译

  2. 会计师事务所任期与审计...

  3. ADO.NET结构与概述英文文献和中文翻译

  4. 信息系统开发与数据库开...

  5. 机器人学入门力学与控制英文文献和中文翻译

  6. 园林植物景观的园林绿化...

  7. 快速成型制造技术英文文献和中文翻译

  8. 巴金《激流三部曲》高觉新的悲剧命运

  9. 浅析中国古代宗法制度

  10. 现代简约美式风格在室内家装中的运用

  11. g-C3N4光催化剂的制备和光催化性能研究

  12. 上市公司股权结构对经营绩效的影响研究

  13. 中国传统元素在游戏角色...

  14. 江苏省某高中学生体质现状的调查研究

  15. C++最短路径算法研究和程序设计

  16. NFC协议物理层的软件实现+文献综述

  17. 高警觉工作人群的元情绪...

  

About

优尔论文网手机版...

主页:http://www.youerw.com

关闭返回