Foreword Nothing contained in any API publication is to be construed as granting any right, by implication or otherwise, for the manufacture, sale, or use of any method, apparatus, or product covered by letters patent。 Neither should anything contained in the publication be construed as insuring anyone against liability for infringement of letters patent。82774

Shell: As used in a standard, “shall” denotes a minimum requirement in order to conform to the specification。

Should: As used in a standard, “should” denotes a recommendation or that which is advised but not required in order to conform to the specification。

This document was produced under API standardization procedures that ensure appropriate notification and participation in the developmental process and is designated as an API standard。 Questions concerning the interpretation of the content of this publication or comments and questions concerning the procedures under which this publication was developed should be directed in writing to the Director of Standards, American Petroleum Institute, 1220 L Street, NW, Washington, DC 20005。 Requests for permission to reproduce or translate all or any part of the material published herein should also be addressed to the director。

Generally, API standards are reviewed and revised, reaffirmed, or withdrawn at least every five years。 A one-time extension of up to two

years may be added to this review cycle。 Status of the publication can be ascertained from the API Standards Department, telephone (202) 682-8000。 A catalog of API publications and materials is published annually by API, 1220 L Street, NW, Washington, DC 20005。

Introduction

The revision of API 6D is developed based on input from API 6D Task Group technical experts。 The technical revisions have been made in order to accommodate the needs of industry and to move this specification to a higher level of service to the petroleum and natural gas industry。

This specification is not intended to inhibit a manufacturer from offering, or the purchaser from accepting, alternative equipment or engineering solutions for the inpidual application。 This may be particularly applicable where there is innovative or developing technology。

1Scope

1。1General

This specification defines the requirements for the design, manufacturing, assembly, testing, and documentation of ball, check, gate, and plug valves for application in pipeline and piping systems for the petroleum and natural gas industries。

This specification is not applicable to subsea pipeline valves, as they are covered by a separate specification, API 6DSS。

This specification is not applicable to valves for pressure ratings exceeding Class 2500。

1。2Conformance

1。2。1Units of Measurement

In this specification, data are expressed in both U。S。 customary (USC) and metric (SI) units。

1。2。2Rounding

Except as otherwise required by this specification, to determine conformance with the specified requirements, observed or calculated values shall be rounded to the nearest unit in the last right-hand place of figures used in expressing the limiting value, in accordance with the rounding method of ASTM E29 or ISO 80000-1。

1。3Conformance with Specification

A quality management system shall be applied to assist conformance with the requirements of this specification。 The manufacturer shall be responsible for conforming with all of the applicable requirements of this specification。

It shall be permissible for the purchaser to make any investigation necessary in order to be assured of conformance by the manufacturer and to reject any material that does not conform。

1。4Processes Requiring Validation

The following operations performed during manufacturing shall be validated, by the manufacturer, in accordance with their quality system as applicable:

上一篇:PLC自动化制造系统英文文献和中文翻译
下一篇:桥式起重机智能防摆控制英文文献和中文翻译

新課改下小學语文洧效阅...

LiMn1-xFexPO4正极材料合成及充放电性能研究

老年2型糖尿病患者运动疗...

张洁小说《无字》中的女性意识

安康汉江网讯

ASP.net+sqlserver企业设备管理系统设计与开发

麦秸秆还田和沼液灌溉对...

网络语言“XX体”研究

互联网教育”变革路径研究进展【7972字】

我国风险投资的发展现状问题及对策分析