菜单
  

    摘要本文研究了钒酸银对镍基复合镀层的制备方法以及该复合镀层在室温和高温下的摩擦学性能。 采用化学法制备钒酸银晶体颗粒,用扫描电镜(SEM)对制备的钒酸银颗粒进行了观察,采用了电沉积复合镀法制备镍基钒酸银复合镀层,用 X射线衍射仪(XRD)、Raman 光谱、能谱仪EDS、扫描电镜(SEM)对不同钒酸银含量的复合镀层、摩擦后的磨痕进行了物相、形貌、成分的分析,用 HT-1000 高温摩擦磨损试验机对镀层进行了室温、200℃、600℃的摩擦学性能测试,对比不同钒酸银添加物含量和不同温度下复合镀层对摩擦学性能的影响,以期获得钒酸银对镍基复合镀层的最佳实验方法和工艺参数。 实验表明:钒酸银对镍基复合镀层确实比纯镍基镀层有更好的减磨效果,单一镍基镀层摩擦系数在0.75左右,复合镀层的摩擦系数在 0.4-0.7之间,尤其在高温时减磨效果明显。钒酸银的含量对复合镀层的摩擦性能也有影响,一定范围内,含量越高减磨效果越明显,但含量超过0.1g/L 时减磨效果有所降低,低于 0.01g/L时效果不明显。   50083
    毕业论文关键词:钒酸银 固体润滑剂 复合镀层 摩擦磨损性能 
    Title     Tribological properties of Ni-based  composites   containing  silver vanadate at room or temperature

     Abstract In this paper, the preparation methods of  Ni-based composite coatings with silver vanadium and its tribological properties at room temperature and high temperature were studied. The silver vanadium particles were prepared by chemical method and were observed by scanning electron microscope  (SEM).Pulse electrodeposition process was used to prepare the silver vanadium-containing /Ni-based composite coatings. Friction and wear scar physical phase, morphology and composition of different silver vanadium content of composite coating analyze with XRD, Raman spectroscopy, SEM, EDS spectrum. The tribological properties of the coating were tested by HT-1000 high temperature friction tester at room temperature, 200℃ and 600 ℃ .  Compare  different silver vanadium  additive content and different temperature composite coating on tribological properties of impact. The results show that  the friction coefficient of Ni-based coating is about 0.75, and  that of  the composite coating is between 0.4-0.7.  Especially at high temperature, the grinding effect is obvious. The silver content of vanadium acid has an effect on the friction property of the composite coating. When the content is more than 0.1g/L, the grinding effect is reduced, and the effect is not obvious when the content is lower than 0.01g/L.   
    Keywords  silver vanadate   solid lubricant   composite coating   friction and wear performance

    目录

    1绪论.1

    1.1引言.1

    1.2固体润滑剂概述1

    1.2.1固体润滑剂..1

    1.2.2常用的制备方法.2

    1.3钒酸银的研究进展.3

    1.3.1钒酸银概述..3

    1.3.2钒酸银的制备方法..3

    1.3.3钒酸银的应用4

    1.4复合镀层简述..4

    1.4.1复合镀层研究背景..4

    1.4.2复合镀层的性能.5

    1.4.3复合镀层制备方法..5

    1.4.4复合电镀的优点.6

    1.5研究目的和研究内容..6

    2实验条件和方法8

    2.1实验流程8

    2.2实验试剂和仪器9

    2.3样品制备9

    2.3.1钒酸银微粒的制备..9

    2.3.2预处理45#碳素结构钢圆盘..10

    2.3.3电镀液的配制..10

    2.3.4添加钒酸银微粒11

    2.3.5电沉积复合镀..11

    2.4摩擦磨损试验.12

    2.4.1摩擦试验设备介绍.12

    2.4.2摩擦磨损试验操作.13

  1. 上一篇:氧化镓纳米晶光电探测器制备及性能
  2. 下一篇:铝泡沫材料制备及组织研究
  1. 不同链长聚二甲基硅氧烷...

  2. 稀土元素Dy对合金涂层结构与高温性能的影响

  3. 金属氧化物对g-C3N4/TiO2复合...

  4. Bi含量对Sn-Bi/Cu界面化合物生长影响的研究

  5. 粉料尺寸对BaTiO3陶瓷烧结工艺研究

  6. 工艺参数对高硅铝合金CMT组织与性能的影响

  7. 表面预处理对水下药芯电弧切割的影响

  8. 浅析中国古代宗法制度

  9. 巴金《激流三部曲》高觉新的悲剧命运

  10. NFC协议物理层的软件实现+文献综述

  11. 江苏省某高中学生体质现状的调查研究

  12. 现代简约美式风格在室内家装中的运用

  13. 上市公司股权结构对经营绩效的影响研究

  14. C++最短路径算法研究和程序设计

  15. 高警觉工作人群的元情绪...

  16. 中国传统元素在游戏角色...

  17. g-C3N4光催化剂的制备和光催化性能研究

  

About

优尔论文网手机版...

主页:http://www.youerw.com

关闭返回