Abstract The non-linear finite element analysis of inland water-way transport barges in collision and grounding is pre-sented in the paper. One of the three analyzed barges is a typical barge operated by the Polish owner, two others are designs developed in Project INBAT. The presented analysis is a part of the thorough strength analysis of the barges which aim is to prove that the designed innova-tive barges have the strength properties not worse than the presently operated. Numerical investigation of colli-sion and grounding was done using the PAM-CRASHTM computer code for numerical simulation of highly non-linear behaviour. The results of the analysis are given and the paper is completed with the conclusions. Keywords collision, grounding, non-linear analysis, finite element method, numerical simulation, inland waterway trans-port Introduction General The analysis of structural strength in collision and grounding is usually associated with sea-going vessels, however, the similar or even greater environmental disaster may be expected as collisions can also cause a serious threaten to the environment e.g. when disastrous oil spill is induced as well as cause serious damage to the struck ( and striking) barge. 58681
Collision and grounding occur quite often in the inland waterway navigation. They will continue to happen no matter how a barge is designed, constructed and operated. The ongoing re-search in this field aims to assess damages, to minimise the consequences of the accidents and suggest ways of improving damage resistance in design. The analysis of structural damage caused by ship colli-sions is complex. The impact response is highly non-linear, involving continuous changes in the geometry of the ship structures. The observed failure modes from ship accidents reveal that the primary energy absorbing mechanisms are: crushing of decks, tearing of bottom plating, folding of web frames, and stretching of shell plating. Two approaches can be distinguished when describing the methods for the analysis of colliding ships: simpli-fied and numerical analysis. Simplified analytical mod-els have been suggested on the basis of rigid-plastic theory to derivation of crushing models for basic struc-tural units. These methods do not account for coupling effects between local and global failure modes.
These models are more suitable for bow collisions where local failure modes are predominant and this coupling can be neglected. Typical for the analytical approach is the Minorsky method (Minorsky, 1959). It has been demonstrated that non-linear FEM simula-tions are reliable and very detailed (Amdahl et al., 1995). Powerful special-purpose FEM packages e.g. DYNA3D, DATRAN and PAM SYSTEM account for large deformation, contact, non-linearity in material properties, and rupture. Published investigations using FEM simulation techniques include: (i) large scale model tests; (ii) real case collision accidents, and (iii) real case grounding accidents. It has been concluded that FEM simulation requires a massive effort both in terms of modelling and computer power. The cost of this analysis is often prohibitively expensive. Kitamura (2002) thoroughly discussed the problem of the finite element analysis pointing out various aspects of such analysis: coupling with hull girder horizontal bending, stretching span and equivalent failure strain, deformation of supporting structure, forward velocity of struck ship, collision angle and bending of bow, folding of flat plate and stiffened panel and partial crushing of bow structure. According to his opinion FEM approach is a unified way that covers all fields of strength analy-ses. In the long run, only a few matters might be left to the discretion of a designer who intends to perform a standardized FEA.  Until early 1990s, the advantage of FEM approach was quite limited compared with the simplified analytical approach. The extent of finite element model and its mesh size were restricted within the unsatisfactory lev-els because of the insufficient capacity of the memory and CPU power in addition to the discouraging compu-tation cost.  Following the successful progress of the modelling technique, the simulations of non-linear elasto-plastic response of complicated hull structure is now practica-ble. Geometrical stress concentration and local bending of plates in the multi-axial stress field can be considered more systematically than ever as well as quasi-uniform membrane stress, provided that due consideration is taken on the mesh size and pattern of finite elements. Time-dependent strain hardening and strain rate effects on the material properties are also counted at every step of the progressive deformation. The finite element mod-els can be recycled many times and the results can be reviewed repeatedly from various aspects on demand. Compared with the implicit finite element code, the explicit finite element code is considered to be more suitable for the collision and grounding simulations of large ships at present. The great advantage of the ex-plicit finite element code is that the simulation model of numerous finite elements can be handled, while the disadvantage is the reduced accuracy due to explicit formulation itself. The disadvantage, however, can be resolved practically by the adoption of fine mesh size and proper time increment.
上一篇:舰船玻璃钢夹芯板缺陷和损伤的影响英文文献和中文翻译
下一篇:现金池英文文献和中文翻译

船舶运动仿真系统英文文献和中文翻译

船舶建造规格书英文文献和中文翻译

船舶自动化系统英文文献和中文翻译

船舶系泊定位系统英文文献和中文翻译

北大西洋航行船舶的波高...

船舶设计中的消防安全性...

船舶与海洋结构物水动力...

网络语言“XX体”研究

我国风险投资的发展现状问题及对策分析

安康汉江网讯

ASP.net+sqlserver企业设备管理系统设计与开发

LiMn1-xFexPO4正极材料合成及充放电性能研究

张洁小说《无字》中的女性意识

互联网教育”变革路径研究进展【7972字】

新課改下小學语文洧效阅...

麦秸秆还田和沼液灌溉对...

老年2型糖尿病患者运动疗...