For the viscosity or density change in the process fluid, the pump will not be affected too much. If there is a damper, for example, in the export side, one row or a limiter filter, pumps will push fluid through them. If the damper changes in their work, that is, if the filters become dirty, blocked, or limiter on the back of the hypertension, the pump will maintain a constant flow, until the device in the weakest parts of the mechanical limit (usually equipped with a torque limiter). For a pump speed, in fact, there are restrictions, which mainly depends on the process fluid, if the transmission is oil, pump can rotate at high speed, but when the fluid is a high viscosity of the polymer melt, such restrictions will be significantly reduced. Promote blood flow into the intake side of the two tooth space is very important, if not fill in this space is full, the pump will not be able to discharge the flow of accurate, so the value of PV (pressure × velocity) is also a limiting factor, and is a process variable. As a result of these restrictions, gear pump manufacturers will provide a range of products, that is, different specifications and emission (perweek to the emission of volume). These pumps will fit the specific application of technology to enable the system to achieve optimal capacity and price.   PEP-II pump shaft gear and a total of one species hardened using technology, will be a longer working life. "D"-type bearing a combination of forced lubrication mechanism, so that the polymer surface by the bearing, and return to the import side of pump to ensure effective lubrication of the rotation axis. This feature reduces the degradation of polymers and the possibility of being stranded. Precision machining of the pump body can "D"-type gear shaft      9  with precision bearings to ensure noneccentric gear shaft to prevent gear wear. Structure and Parkool PTFE sealing lip sealed water cooled sealed together. This shaft seal does not actually contact the surface, it is the principle of the sealing polymer to a semimolten state cooling and the formation of self sealing. Can also be used Rheoseal sealing, seal it inside the table are reverse spiral groove processing, the polymer can be imported back to the antipressure. In order to facilitate the installation, the manufacturer has designed the installation of a ring bolt, so that the flange and install other equipment line, which makes the manufacture of tube flange easier. PEP-II with a gear pump with the pump to match the specifications of the heating elements for the user matching, which ensures rapid heating and heat control. Heating the body and pump in different ways, the damage to these components is limited to a board, the pump has nothing to do with the whole.   Gear pump by an independent motor drive, to be effective in blocking the upper reaches of the pressure pulsation and flow fluctuations. Gear pump in the outlet of the pressure fluctuation can be controlled within 1%. In the extrusion production line using a gear pump, can increase the output flow rate of material in the extruder to reduce the shear and residence time to reduce the extrusion temperature and pressure fluctuation in order to enhance productivity and product quality.  The role of the hydraulic system is to help humanity work. Mainly by the implementation of components to rotate or pressure into a reciprocating motion. 

Hydraulic principle:it consists of two cylinders of different sizes and composition of fluid in the fluid full of water or oil. Water is called "hydraulic press"; the said oilfilled "hydraulic machine." Each of the two liquid a sliding piston, if the increase in the small piston on the pressure of a certain value, according to Pascal's law, small piston to the pressure of the pressure through the liquid passed to the large piston, piston top will go a long way to go. Based cross-sectional area of the small piston is S1, plus a small piston in the downward pressure on the F1. Thus, a small piston on the liquid pressure to P = F1/SI, Can be the same size in all directions to the transmission of liquid. "By the large piston is also equivalent to the inevitable pressure P. If the large piston is the cross-sectional area S2, the pressure P on the piston in the upward pressure generated F2 = PxS2 Cross-sectional area is a small multiple of the piston cross-sectional area. From the type known to add in a small piston of a smaller force, the piston will be in great force, for which the hydraulic machine used to suppress plywood, oil, extract heavy objects, such as forging steel.      Hydraulic system and hydraulic power control signal is composed of two parts, the signal control of some parts of the hydraulic power used to drive the control valve movement.      Part of the hydraulic power means that the circuit diagram used to show the different10  functions of the interrelationship between components. Containing the source of hydraulic pump, hydraulic motor and auxiliary components; hydraulic control part contains a variety of control valves, used to control the flow of oil, pressure and direction; operative or hydraulic cylinder with hydraulic motors, according to the actual requirements of their choice.  In the analysis and design of the actual task, the general block diagram shows the actual operation of equipment. Hollow arrow indicates the signal flow, while the solid arrows that energy flow.       Basic hydraulic circuit of the action sequence Control components (two four-way valve) and the spring to reset for the implementation of components (double-acting hydraulic cylinder), as well as the extending and retracting the relief valve opened and closed. For the implementation of components and control components, presentations are based on the corresponding circuit diagram symbols, it also introduced ready made circuit diagram symbols.  Working principle of the system, you can turn on all circuits to code. If the first implementation of components numbered 0, the control components associated with the identifier is 1. Out with the implementation of components corresponding to the identifier for the even components, then retracting and implementation of components corresponding to the identifier for the odd components. Hydraulic circuit carried out not only to deal with numbers, but also to deal with the actual device ID, in order to detect system failures.  DIN ISO1219-2 standard definition of the number of component composition, which includes the following four parts: device ID, circuit ID, component ID and component ID. The entire system if only one device, device number may be omitted.       Practice, another way is to code all of the hydraulic system components for numbers at this time, components and component code should be consistent with the list of numbers. This method is particularly applicable to complex hydraulic control system, each control loop are the corresponding number with the system.  With mechanical transmission, electrical transmission compared to the hydraulic drive has the following advantages:       1, a variety of hydraulic components, can easily and flexibly to layout.   2, light weight, small size, small inertia, fast response.   3, to facilitate manipulation of control, enabling a wide range of stepless speed regulation (speed range of 2000:1).       4, to achieve overload protection automatically.       5, the general use of mineral oil as a working medium, the relative motion can be self-lubricating surface, long service life.      6, it is easy to achieve linear motio