1。Introduction1。1。This specification applies to aluminum alloys for compressor housings。

1。2。This specification does not constitute a grant of license, sublicense or any actual or implied right to use any patent or other intellectual property right of a third party which may be infringed by compositions, materials or components (collectively Supplied Goods), or processes employed for preparation, manufacture or fabrication of Supplied Goods, meeting the requirements defined herein。 Suppliers further warrant that Supplied Goods do not infringe any patent or other intellectual property right of a third party。83165

1。3。Upon request, in a form and substance satisfactory to enable Honeywell to meet its compliance obligations with regards to Regulation (EC) No。 1907/2006 (“REACH”), ELV Directive No。 2000-53-EC and associated annexes, or similar laws or regulations identified by Honeywell, Vendors will provide Honeywell with complete information regarding the chemical composition of any Goods (substances, preparations, mixtures, alloys or goods) supplied under this Materials Specification, including all safety information required under REACH and information regarding the registration or pre-registration status of any Goods pursuant to REACH。论文网

1。4。Vendors shall ensure that all information requested in paragraphs 7。1。1 and 7。2。1 are explicitly stated for each part number on the drawing。 The lack of this information shall be considered as non-compliance and the drawing shall be updated。 Vendors shall mention this specification and its revision letter, and international material designation in all quotations and  when acknowledging purchase orders。

2。Scope

This specification describes the condition, chemical and technical requirements for aluminum alloy 356 for compressor housings。

3。Definitions, Abbreviations and Symbols

ASTM American Society for Testing Materials

ECHA European Chemicals Agency

ELV End of Life Vehicles Regulations

EN European Standard ‘EuroNorm’

PI Process Instruction (a Honeywell Turbo Technologies Document)

QCI Quality Control Instruction (a Honeywell Turbo Technologies Document) REACH Registration, Evaluation, Authorisation and restriction of Chemicals SVHC Substances of Very High Concern

Turbo Technologies NUMBER IDM-4234

REVISION

N

TITLE

MATERIALS SPECIFICATION CAST ALUMINUM ALLOY – 356-F BY

Ondrej Bojda

DATE

12/02/11 Page

3 of 8

4。List of Related Documents

EN ISO 6506-1 Metallic Materials – Brinell Hardness Test – Part 1: Test Method

QCI-9310-175 Standards for Retesting of Properties of Materials

QCI-9310-239 Tensile Testing of Metallic Materials

5。Condition Requirements

5。1。Condition

Housings shall be received in the as-cast condition (F temper)。

6。Chemical Requirements

6。1。Chemical Composition

6。1。1。The chemical composition of material supplied to this specification shall conform to the following composition。 The nominal content should be targeted for each element unless otherwise specified on the component drawing。

6。1。2。The other elements (OET) shall not contain the Candidate (SVHC) List substances published by ECHA or shall not contain any restricted substances such as lead, cadmium, mercury, hexavalent chromium as prescribed in ELV Directive No。 2000-53-EC and associated annexes or other similar laws or regulations available for restricting substances globally in any region as updated from time to time。 In case OET contains SVHC then the percentage present needs to be notified。文献综述

上一篇:快速成型制造技术英文文献和中文翻译
下一篇:干涉配合轴的应力分析英文文献和中文翻译

可变压缩比柴油发动机英文文献和中文翻译

张洁小说《无字》中的女性意识

老年2型糖尿病患者运动疗...

我国风险投资的发展现状问题及对策分析

ASP.net+sqlserver企业设备管理系统设计与开发

网络语言“XX体”研究

互联网教育”变革路径研究进展【7972字】

麦秸秆还田和沼液灌溉对...

LiMn1-xFexPO4正极材料合成及充放电性能研究

新課改下小學语文洧效阅...

安康汉江网讯